RavenFull, Plany depronowców
[ Pobierz całość w formacie PDF ]
1/64" ply doublers on both
sides of fuselage (see side view)
6mm Depron Fuse
Notes on the fuse:
If you are going for all out light weight, consider leaving
out the fuse spar. The side plates are strong enough for
anything in flight, but will not be quite as tough for rough
landings/crashes. Make sure to use 15-30 minute epoxy or
shoogoo for the main parts...5 min and foam CA are not
strongenough, and will crack under the torque.
3/8"x3/8" Hardwood motor block
Groove block to fit carbon rod.
If using GWS 350 Drive, mount
block on Carbon rod so that the
prop/drive shaft is in the same
location as shown on plans.
Molded Carbon Gear Legs
3/16" zipties
4mm Carbon Spar
6mm Depron Fuse Rails
Aileron Servo
(HS-56HB Shown)
(1 Each Side)
Elevator Servo
(HS-56HB Shown)
LiPo Battery
Rudder Servo
(HS-56HB Shown)
2100(3s2p)
Carbon Tail wheel bracket
1/64 ply gear mount plates
1/16" wire wheel axel/steering arm
(Bend 90 deg. at the top to form
a control arm. Use clamp on ball
link to attach to rudder control horn)
Use Cotterpin to adjust
tension on pull-pull system.
Mount using Dubro EZ Conectors
Hacker B20-15L shown
Molded Carbon Fiber Gear
Vacuum Formed
Wheel Pants
Cut Control horns from 1/32"
ply or a plastic coffee can lid.
Motor/Battery Info
Push/Pull
Pull Pull
All hinging for control surfaces can be packing
tape or actual hinges. I prefer robart hinge
points epoxied in place for the added longivity
and control freeness.
Motor Gearing Prop Battery Amp Draw Thrust
GWS EPS350C DS (6.6:1) GWS 12x6 2s1p Lipo 9.5 17.1 oz.
GWS EPS350C DS (6.6:1) GWS 11x4.7 3s1p Lipo 11.5 24.3 oz.
Hacker B20-26S 4:1 Planetary APC 11x4.7 3s1p LiPo 11 amps 22.1 oz.
Hacker B20-31S 4:1 Planetary APC 11x4.7 3s1p LiPo 7.7 amps 18.6 oz.
Hacker B20-15L 4:1 Planetary APC 11x4.7 3s2p LiPo 19.5 amps 38.5 oz.
Hacker B20-15L 4:1 Planetary APC 11x4.7 2s1p LiPo 10.8 amps 20.6 oz.
Hacker B20-18L 4:1 Planetary APC 11x4.7 3s1p LiPo 11.7 amps 27.7 oz.
Hacker B20-18L 4:1 Planetary APC 12x6 3s2p LiPo 19 amps 36.7 oz.
Razor RZ300 GWS/5.3:1 GWS 11x4.7 2s1p LiPo 8.8 amps 15.7 oz.
Razor RZ300 GWS/5.3:1 GWS 12x6 2s1p LiPo 9.9 amps 18.5 oz.
Razor RZ300 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 12 amps 26 oz.
Razor RZ350 GWS/6.6:1 GWS 12x6 3s1p LiPo 12.4 amps 27 oz.
Razor RZ350 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 8.7 amps 21.2 oz.
Razor MicroHeli v2 GWS/6.6:1 GWS 12x6 3s1p LiPo 8.9 amps 22.8 oz.
PJS 3D 500 Direct APC 10x4.7 3s2p LiPo 16.4 amps 21.9 oz.
PJS 3D 550 Direct APC 10x4.7 3s2p LiPo 13.8 amps 20.7 oz.
HiMax HA2015-3600 GWS/5.3:1 GWS 12x6 3s1p LiPo 8.7 amps 20.5 oz.
HiMax HA2015-3600 GWS/6.6:1 GWS 12x6 3s1p LiPo 6.5 amps 18.5 oz.
HiMax HA2015-4100 GWS/6.6:1 GWS 12x6 3s1p LiPo 11.2 amps 26.4 oz.
HiMax HA2015-4100 GWS/5.3:1 GWS 11x4.7 3s1p LiPo 11.6 amps 25.2 oz.
HiMax HA2015-5400 GWS/6.6:1 GWS 12x6 2s1p LiPo 10.2 amps 17.8 oz.
HiMax HA2025-3236 3.6:1 Planetary APC 11x4.7 3s2p LiPo 14 amps 29.3 oz.
HiMax HA2025-3236 3.6:1 Planetary APC 12x6 3s2p LiPo 17 amps 32.2 oz.
HiMax HA2025-4236 4.3:1 Planetary APC 11x4.7 3s2p Lipo 20.2 amps 38.1 oz.
Hacker B20-15L shown
6
Mount Battery Pack
with 1" Velcro strap.
Also use adhesive
Velcro on the side of
fuselage and back of
pack to secure in
place.
5
4
3
2
1
1
2
3
4
5
6
Weight
10.5-15.5 oz.
Thrust
24-39 oz.
Radio
4-5 Chanel
Area
301.4 in2
Cut a "V" groove
in foam for
spars. Pull spar
through groove
to make round
Loading
4.2-7.2 oz/ft2
WWW.3DFOAMY.COM
Specs:
The Raven 3D
3D Foamy
Copyright © 2004 3DFoamy.com.
All rights reserved.
Designed and Drawn by Levi Jordan
Updated: 03/3/04.
[ Pobierz całość w formacie PDF ]