Range-Rover-Manual-Exhaust, Land Rover
[ Pobierz całość w formacie PDF ]
PO;;; 1987
MANIFOLD AND EXHAUST SYSTEM
[30
1
EXHAUST SYSTEM COMPLETE
‘.
J
EXHAUST SYSTEM COMPLETE
WARNING: To prevent personal injury occurring
from a hot exh‘aust system, DO NOT attempt to
1:’
y:. Y...,.....
,..’
NOTE: Ensure that no exhaust leaks are evident
disconnect any of the components until ample
:
in either a new or an old exhaust system, as this
time has elapsed to allow the exhaust system to
will affect vehicle performance, and contravene
cool.
;,. :;:A:<?..
.‘i.’
Federal emission regulations.
Continued
REVISED: DEC. 87
1
:
:. ., ..
,: ,: . .:v.
MANIFOLD AND EXHAUST SYSTEM
,\ ..
Remove and refit
EXHAUST MANIFOLD
Removing
Remove and refit
1. Raise the vehicle on a suitable hoist and apply
the parking brake.
Left hand
2. Remove the four fixings securing the grass
shield (if fitted) to the mounting bracket at the
centre catalyst.
Right hand
Removing
3. Withdraw the grass shield from the bracket.
1. Disconnect the front exhaust pipe(s) from the
manifold(s).
2. Tap back the bolt locking tabs and remove the
eight bolts, lock tabs and washers.
3. Remove the manifold(s) and old gaskets.
4. Disconnect the electrical plugs from the
Lambda sensors.
5. Remove the nuts and disconnect the front
pipe(s) from the manifold(s) and remove the
gaskets.
6. Loosen the pinch bolt clamps securing the
front pipe to the intermediate pipe.
7. Withdraw the front pipe(s) with catalysts.
8. Remove three bolts securing the intermediate
pipe to the centre catalyst and withdraw the
doughnut.
Refitting
4. Ensure that the mating surfaces of the cylinder
head and exhaust manifold are clean and
smooth.
5. Coat the threads of each bolt with anti-seize
compound.
9. Remove the U-bolt from the pipe mounting
bracket.
6. Place the manifold and new gaskets in position
on the cylinder head and fit the securing bolts,
new lockplates and plain washers. The plain
washers are fitted between the manifold and
lockplates.
* 10. Withdraw the intermediate pipe.
11. Remove the U-bolt securing the centre catalyst
to the main muffler.
12. Withdraw the catalyst.
13. Remove the U-bolt from the tail pipe
mounting bracket.
14. Withdraw the tail pipe and rear muffler.
7. Evenly tighten the manifold bolts to the
correct torque, see torque values-section 06,
and bend over the lockplate tabs. i
8. Reconnect the front exhaust pipe, using new
exhaust flange gaskets.
Refitting
NOTE: Apply Firegum Putty, Part No. 15608
to all exhaust system joints with the
exception of the exhaust flange to manifold
flange where new gaskets should be fitted.
..
INTAKE MANIFOLD
*I
The removal and refit of the intake manifold is
incorporated
‘. . .
in the Fuel Injection System,
15. Reverse the removal instructions.
Section 19.
2
REVISED: DEC. 87
.‘&S
MANIFOLD AND EXHAUST SYSTEM
j
;:
: .,.. .,,.:
RR2387E
.,,
EXHAUST SYSTEM COMPLETE
Remove and refit
NOTE: Ensure that no exhaust leaks are evident
in either a new or old exhaust system, as this
will affect vehicle performance, and contravene
Federal emission regulations.
Removing
Tail pipe and rear muffler
1.
Raise the vehicle on a suitable hoist and apply
the parking brake.
Remove the three bolts s&uring the tail pipe
assembly to the intermediate pipe assembly.
Remove the bolt securing the rear mounting
bracket. to the chassis.
Maneuver the tail pipe over the rear axle and
remove from the vehicle.
Retain the doughnut from the intermediate
pipe for reassembly.
WARNING: To prevent personal injury occurring
from a hot exhaust system, DO NOT attempt to
disconnect any ot the components until ample
time has elapsed to allow the exhaust system to
cool.
2.
3.
4.
5.
Continued
ADDITION: SEPT. 88
3
,.,,
,. .’
‘..’
6. Detach the rubber from the tailpipe and
hanger.
intermediate pipe and centre muffler
7. Remove the three bolts securing the right
hand branch of the intermediate pipe to the
right hand catalyst.
8. Release the pinch bolt clamp securing the left
hand branch of the intermediate pipe to the
left hand catalyst and slide the clamp along
the pipe.
9. Remove the bolts securing the front and rear
hanger brackets to the chassis.
10. Detach the rubbers from the main muffler
assembly and hangers.
11. Carefully separate the intermediate pipes from
the front downpipes.
12. Retain the doughnut from the right hand joint.
Front downpipes
13. Disconnect both Lambda sensor multiplugs.
14. Remove the nuts and release the front
downpipes from the manifolds, discard the
gaskets.
Refitting
15. lf the original system is being refitted, examine
the system for damage and general condition
renew sections as necessary.
16.
Clean any previous putty from the doughnuts
and exhaust pipe joints.
17. Fit NEW gaskets to the manifold joint face.
NOTE: Apply exhaust sealer to all exhaust system
joints with the exception of the exhaust flange
to manifold flange.
18. Reverse the removal instructions.
19. Examine a new or original system for leaks and
ensure that the system does not foul any
underbody components. If exhaust leaks or
interference exists loosen the joints reseal and
reset as necessary.
4
ADDITION: SEPT. 88
_‘.
:
‘.
..‘: .,
MANIFOLD AND EXHAUST SYSTEM 130 1
RR277-m
EXHAUST SYSTEM COMPLETE
Remove and refit
To improve sealing and accuracy of assembly, 1990
model year vehicles have a new two piece exhaust
svstem.
Removing
Raise the vehicle on a suit$ble ramp. apply the
parking brake.
Catalyst vehicles only: Disconnect the two
lambda sensor wiring connectors.
Remove the two bolts securing the rear
exhaust
NOTE: Ensure that no exhaust leaks are evident
in either a new or old exhaust system, as this
will affect vehicle performance.
assembly to
the front exhaust
. ..,’ ,
: ‘.
~..:.::!:.
disconnect any of the components until ample
time has elapsed to allow the exhaust system to
cool.
assembly.
Remove the nuts and release the front
downpipes fromt the manifolds. Discard the
gaskets.
ADDITION: SEPT. 89
5
WARNING: To prevent personal injury occurring
from a hot exhaust system, DO NOT attempt to
. .
[ Pobierz całość w formacie PDF ]